300-510 Practice Online

Question 1

Refer to the exhibit.

R1 is directly connected to R2 and R3. R1 is in BGP AS 123, R2 is in BGP AS 2, and R3

is in BGP AS 3. Assume that there is no connectivity issue between R1, R2 and R1, R3. Which result between

BGP peers R1, R2 and R1, R3 is true?

A : The BGP session does not come up between R1 and R2 and between R1 and R3.

B : The BGP session comes up between R1 and R2 and between R1 and R3.

C : The BGP session comes up between R1 and R3, but not between R1 and R2.

D : The BGP session comes up between R1 and R2, but not between R1 and R3

Answer: B

Question 2

Refer to the exhibits.

All links inside the network are configured at a default cost of one inside the fully converged OSPF domain. Given the configuration from XR1, which interface does traffic from XR1 that is destined to the loopback interface of XR6 select for the exiting interface?

A : Interface GigabitElhemet 0/0. The tie breaker of the node index priority is lower and trumps the path cost.

B : Interface GigabitEthernet 0/1. The tie breaker of the path cost being lower. The node index priority does not impact this selection process.

C : Interface GigabitEthernet 0/1. The tie breaker of the node index priority is lower and trumps the path cost.

D : Interface GigabitEthernet 0/0. The tier breaker of the path cost being lower. The node index priority does not impact this selection process.

Answer: A

Question 3

Refer to the exhibit.

A service provider technician is working on a multicast issue for a customer. While

checking the multicast table, the technician notices that no flags are present for the (1.1.1.1, 239.1.1.1) entry, yet flags are present for the (1.1.1.1, 232.1.1.1) entry.

Which factor might explain this issue?

A : Only the administratively scoped range is permitted

B : Only ASM is permitted

C : Only the default SSM range is permitted

D : Only GLOP is permitted

Answer: C

Question 4

Refer to the exhibit.

A network engineer configured routers R1 and R5 to run in IS-IS Level 1 mode and router R6 to run in IS-IS Level 2 mode. All other routers are running as Level 1 / Level 2 routers. An engineer expects traffic from R1 to R6 to pass via R2, but IS-IS routing has calculated the best path via R4. Which action corrects the problem?

A : Configure all routers as Level 1 routers.

B :

Remove the link metric for the link from router R1 to router R2.

C : Change the link metric for the link from router R1 to router R2 to 1.

D : Configure all routers as Level 1 / Level 2 routers.

Answer: C

Question 5

Refer to the exhibit. Router R1 is expected to receive routes that originate from AS 65547 only. However, R1 is receiving routes from AS 65547 and several other ASs that are directly attached to it. Which change to the AS path permit filter corrects the problem?

A : Change the regular expression to $.

B : Change the regular expression to.*.

C : Change the regular expression to _65547_.

D : Change the regular expression to A65547$

Answer: D

Name:	Implementing Cisco Service Provider Advanced Routing Solutions
Exam Code:	300-510
Certification:	CCNP Service Provider
Vendor:	Cisco
Total Questions:	216
Last Updated:	Apr 25, 2024

Download Demo 300-510 Dumps

Create Account

Password Recovery

300-510 Practice Online

Download Demo 300-510 Dumps

Member Login

Create Account

Password Recovery

300-510 Practice Online